非標自動化設備初次投入使用時的檢查調試細節有哪些？
發布時間：
2023-02-10 11:26
標準的自動化設備滿足不了需求差異化的生產需求，這時候就需要企業根據自己的實際生產需求及生產線的特點來定制非標自動化設備，在初次投入使用時需要進行檢查和調試，紅寶自動化就設備調試細節給大家做一下詳細的介紹。
Standard automation equipment can not meet the demand differentiation of production needs. At this time, enterprises need to customize non-standard automation equipment according to their actual production needs and the characteristics of the production line. When they are put into use for the first time, they need to be checked and debugged. Hongbao automation will give you a detailed introduction of the equipment debugging details.
非標自動化設備運行前的電氣檢查調試：
Electrical inspection and commissioning of non-standard automation equipment before operation:
控制電路檢查（主電路斷開，接通控制電路空載試驗）
Control circuit check (no load test with main circuit disconnected and connected)
1、檢查各電路及元器件的動作順序是否正確。
Check whether the action sequence of each circuit and component is correct.
2、檢查連鎖環節及聯動裝置、各保護環節等信號裝置的動作是否正確。
Check whether the actions of interlocking links, linkage devices, protection links and other signal devices are correct.
3、檢查行程開關、限位開關，并調整使其動作在準確位置。
Check the travel switch and limit switch, and adjust it to make it move in the accurate position.
4、檢查各元器件觸頭接觸的可靠性、動作的靈活性、應無卡住、粘住或停滯現象，且無過大的噪聲及線圈過熱現象。
Check the contact reliability of each component contact and the flexibility of action. There should be no jamming, sticking or stagnation, and no excessive noise and coil overheating.
主電路檢查：按電氣原理圖要求的參數對非標自動化設備主電路進行調整。
Main circuit inspection: adjust the main circuit of non-standard automation equipment according to the parameters required by the electrical schematic diagram.
非標自動化設備一般檢查：
General inspection for non-standard automation equipment:
1、對各元器件進行清掃，檢查接觸器、繼電器等可動器件的動作是否靈活，接線頭是否牢固、是否有漏接、錯接。
Clean the components, check whether the action of contactor, relay and other movable devices is flexible, whether the connector is firm, whether there is leakage or wrong connection.
2、檢查主電路接線，注意極性。
Check the main circuit wiring and pay attention to the polarity.
3、檢查各種控制與保護電器，如時間繼電器、熱繼電器等的整定值是否符合線路要求，熔斷器的熔體是否合適等。
Check whether the setting values of various control and protection electrical appliances, such as time relay and thermal relay, meet the line requirements, and whether the fuse melt is suitable.
4、檢查行程開關、限位開關等的、觸頭使用是否正確，轉動是否靈活及內部有無異物。
Check whether the contact of travel switch and limit switch is used correctly, whether the rotation is flexible and whether there are foreign matters inside.
5、檢查保護接地系統是否規范。接地線應牢固并保證接觸良好。
Check whether the protective grounding system is standard. The grounding wire shall be firm and in good contact.
非標自動化設備絕緣檢查：
Insulation inspection of non-standard automation equipment:
1、清潔灰塵、油污及碎物。
Clean dust, oil and debris.
2、檢查導電部位對地絕緣，如電器的金屬外殼、底座、支架或鐵心等；兩個不同電路間，如交流電路的各相之間、主電路與控制電路、保護顯示電路之間及交直流電路間，各絕緣應不小于0.5兆歐。
Check the insulation of conductive parts to the ground, such as the metal shell, base, bracket or iron core of electrical appliances; the insulation between two different circuits, such as the phases of the AC circuit, the main circuit and the control circuit, the protection display circuit and the AC / DC circuit, should not be less than 0.5 megohm.
定制非標自動化設備的研發和生產在3C消費類電子、汽車、半導體行業、物聯網等行業被廣泛應用，并在行業內得到了良好的推廣。山東紅寶自動化有限公司更注重的是非標自動化設備的簡潔設計，而且功能是自定義操作的，滿足更多生產型企業的生產需求。
The R & D and production of customized non-standard automation equipment is widely used in 3C consumer electronics, automobile, semiconductor industry, Internet of things and other industries, and has been well promoted in the industry. Shandong Hongbao Automation Co., Ltd. pays more attention to the simple design of non-standard automation equipment, and the function is user-defined operation to meet the production needs of more production-oriented enterprises.
非標自動化設備