非標自動化設備在驗收過程中有哪些細節要注意？
發布時間：
2023-02-10 11:28
非標自動化設備的構思、設計、定制等一系列的規劃都需要認真完成， 最后的驗收工作也十分重要。那么對于消費者而言在非標自動化設備驗收的環節有哪些細節需要注意呢？
The conception, design and customization of non-standard automation equipment need to be carefully completed, and the final acceptance work is also very important. So for consumers, what details need to be paid attention to in the acceptance of non-standard automation equipment?
驗收設備性能是否穩定？
Is the performance of acceptance equipment stable?
工作效率能否達到預期？
Can work efficiency meet expectations?
操作是否便利？
Is the operation convenient?
是否符合設備制造的安全規范等買賣雙方協議的要求？
Whether it meets the requirements of the agreement between the buyer and the seller, such as the safety specification of equipment manufacturing?
另外更加細致的工作，就是對于設備的一些細節部分的質量做好考核，像設備中焊接件的驗收。
In addition, more detailed work is to check the quality of some details of the equipment, such as the acceptance of welding parts in the equipment.
常規來說，焊縫必須到達GB50205-2001鋼結構工程施工驗收規范中規定的《三級焊縫的驗收規范》，部分非標需到達國家規定的二級焊縫規范。
Generally speaking, the weld must reach the "code for acceptance of class III weld" in the code for acceptance of steel structure engineering construction (GB 50205-2001), and some non-standard welds must meet the national secondary weld code.
按照圖紙對照相關管口方位和地腳螺栓中心距,對相關設備焊縫檢查有無突出太多,容器不圓度多少等等。
According to the drawing, check whether there is too much protrusion on the welding seam of the relevant equipment and the out of roundness of the container according to the relevant pipe mouth orientation and anchor bolt center distance.
還有需要檢驗非標自動化設備的制作鋼材質量，對全部鋼板應作超聲波探傷檢查，22mm以下的鋼板，要取鋼板數量的10%進行“米”字形超聲波探傷檢查。如發現有缺陷，應重新對全部鋼板進行檢查。
In addition, it is necessary to inspect the quality of steel produced by non-standard automation equipment. Ultrasonic flaw detection should be carried out on all steel plates. For steel plates below 22mm, 10% of the steel plates should be taken for "meter" ultrasonic flaw detection. If defects are found, all steel plates shall be inspected again.
在檢查驗收鋼板時，看表面是否光滑平整，不得有氣泡、結疤、坡口邊不得有夾層、裂紋等缺陷。
When checking and accepting the steel plate, check whether the surface is smooth and flat, and there are no bubbles, scabs, interlayer and cracks on the groove edge.
以上各環節確認之后，就需要在非標自動化設備正常工作的過程中進行檢查，出現任何問題要及時反饋技術工程師。只有非標自動化設備的整個環節順暢之后，才能正常投入使用。
After the above links are confirmed, it is necessary to check the non-standard automation equipment in the normal operation process, and any problems should be timely fed back to the technical engineer. Only after the whole link of non-standard automation equipment is smooth, can it be put into use normally.
非標自動化設備